Leading 10 usual forklift crashes ， forklift procedure should pay attention to these issues ！.

Don't take too lightly the forklift at the office. If the operation is bad, there will be severe accidents in minutes, and there are many crashes including forklifts.

Case 1: The forklift freight obstructed the motorist's view, and the person ahead can not be located, leading to a moving crash.
Case 2: In order to maintain the balance of the forklift when lifting hefty products, the staff members used their body weight as the counterweight, which virtually caused casualties.
Case 3: The width of the forklift cargo goes beyond the permitted size of the course and holds on the roadside shelf, which almost causes an accident.
Instance 4: Forklift is speeding up and surrender during a turn.
Case 5: The forklift driver did not notice the pedestrian, and the pedestrian did not notice the forklift.
Instance 6: The forklift raises the workers illegally, the forklift vehicle driver does not put on the seat belt, the forklift lifter falls and the vehicle driver is squashed when the forklift rolls over.
Case 7: The forklift vehicle driver did not use a seat belt and dropped from the automobile when it rolled over and was squashed.
Forklift operation should pay attention to these issues ：.

Begin.
1. Before beginning, observe the surroundings, and after confirming that there are no barriers that hinder the safety and security of driving, beep the horn first and then begin.
2. For automobiles with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) gauge have to be risk-free prior to beginning.
3. When the forklift starts with a load, the vehicle driver must first verify that the load is steady and reputable.
4. The beginning needs to be slow and consistent.

Driving.
1. When driving, the elevation in between the bottom end of the fork and the ground ought to be maintained 300mm-400mm, and the mast ought to be slanted backward. .
2. Do not raise the fork too high when driving. When going into and leaving the work site or while driving, beware that there will certainly be no obstacles in the sky. When the tons is taking a trip, the fork should not be elevated too high, which will influence the stability of the forklift. .
3. After discharging, the fork must be lowered to the normal driving setting prior to driving. .
4. When turning, if there are pedestrians or cars close by, the driving signal needs to be issued first. High-speed sharp turns are forbidden. High-speed doglegs will certainly cause the car to shed side security and topple. .
5. When the forklift is downhill, it is strictly forbidden to shut off the flame and slide, and it is prohibited to brake instantly while driving with loads unless there are special situations.
6. When the forklift is running, it needs to comply with the website traffic rules in the factory and need to maintain a particular safety and security range from the lorry ahead. .
7. When the forklift is running, the lots must be in the lowest position that does not hinder the driving, and the gantry ought to be appropriately tilted back. The lots shall not be elevated other than when piling or filling. .
8. The elevation of the tons need to not block the chauffeur's sight. In special circumstances, when the item influences the forward vision, drive at a reduced rate when reversing.
9. It is prohibited to turn on the ramp, nor to drive throughout the ramp. .
10. The secure driving rate of the forklift in the factory area is 5 km/h, and it must drive securely at a reduced speed when entering the manufacturing workshop location. .
11. When the forklift is lifted, lifted or driven, it is restricted for employees to base on the fork to hold items and play a stabilizing duty. .
12. If issues are found, they will certainly be fixed and reported in a prompt manner, and they will certainly never ever run with diseases or conceal them.

filling and discharging.
1. When fork-loading items, the range between both forks must be changed as required to make the tons of the two forks well balanced and not skewed, and one side of the item need to protest the rack. .
2. It is restricted to deal with a solitary fork or utilize a fork top or pull. In unique situations, safety and security warning signs should be set up to advise surrounding pedestrians. .
3. In the process of filling and unloading things, the forklift should be stopped with the brake. .
4. The speed of the lorry ought to be slow-moving and consistent. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled things and hurt individuals. .
5. When using a fork to fork the goods, the fork must be as deep as possible under the tons, and it needs to be noted that the fork pointer should not touch various other items or objects. The lots should be supported with minimal back tilt of the gantry to ensure that the lots does not slide in reverse. The pole can be tilted ahead a little when the load is reduced to permit very easy placement of the tons and removal of the forks. .
6. It is forbidden to fork goods at high speed and ram tough objects with the fork head. .
7. When the forklift is working, it is prohibited for individuals to loaf the fork, so as to prevent the collapse of the goods and harm individuals. .
8. Straining is prohibited, and it is restricted to utilize forks to raise employees to engage in high-altitude operations to avoid high-altitude falling mishaps. .
9. It is not permitted to make use of the brake inertia to slide, place, round or roll objects. .
10. It is not allowed to use forks to pick, turn pallet discharge.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork impend. Prior to leaving the forklift, you need to dump the goods or reduced the fork structure.
2. Draw the hand brake take care of to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for unique scenarios, such as the motorist does not leave the lorry's view and does not go beyond 1 min).
4. Eliminate the secret. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the appearance should be examined, and gas, lubing oil and cooling water ought to be added.
2. Check the safety and security efficiency of starting, running and stopping.
3. Check whether the lights and horn signals are full and efficient.
4. During the operation of the forklift, inspect whether the pressure and temperature are regular.
5. After the forklift is running, the external leakage ought to also be examined and the seals should be changed in time.

Forklift Safety Operation Specifications.
1. You must inspect before leaving the car;.
2. When you come across a person in front of you during driving, you should send out a signal at a distance of 5 m;.
3. The driving rate in the factory does not go beyond 5 km/h;.
4. When driving, the low point of the freight must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming need to not be also sharp to avoid the tendency of Stand-on Electric Pallet Stacker " cost-free turning";.
6. Running up and down the slope needs to be sluggish and uniform, and no turning on the slope is enabled.
7. Do not drive throughout the gradient. When the gradient is higher than 10%, the lorry ought to be driven in reverse when worsening;.
8. When the forklift workers bring the goods and move forward, if they come across large or heavy items and go to the driver's line of sight, they should take the reversing workout
.
The "Eight Prohibitions" ought to be adhered to Stand-on Electric Pallet Stacker in the procedure.
1. Single fork procedure is not enabled.
2. It is not allowed to raise the goods for far away driving.
3. It is not permitted to get the goods by handing over the pallet with the fork.
4. It is not permitted to straight shovel chemicals, flammables and other unsafe chemicals with forks.
5. It is not allowed to utilize inertia force to grab the goods.
6. It is not enabled to utilize stopping pressure to exile round or easy-to-roll things.
7. It is not enabled to bring people to work on the pallet or fork, and it is purely forbidden to stand under the fork after the fork is raised.
8. Do not drive laterally on slopes
.
Parking is not allowed under the list below problems.
1. Curves, slim roadways, train crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an challenge on one side of the roadway, the opposite side of the section with the very same size as the challenge should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844